-
KS AX3500
-
KS AX3300
POWER AMPLIFIER: INSTRUCTIONS
1204MNMMDWASH
EN, FR
© 2004 Victor Company of Japan, Limited
AMPLIFICATEUR DE PUISSANCE: MANUEL D’INSTRUCTIONS
LVT1329-001A
[J/E/U]
POWER SUPPLY
ENGLISH
KS-AX3500
KS-AX3300
Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure
your complete understanding and to obtain the best possible performance from the unit.
For safety....
•
Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.
• Stop the car before performing any complicated operations.
CAUTIONS AND NOTES
CAUTION
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems.
• This unit uses BTL (Balanced Trans-formerless) amplifier circuitry, i.e., floating ground system,
so please comply with the following:
To prevent short circuits while making connections, keep the battery’s negative terminal
disconnected.
• When using a power cord, be sure to place the 30 A fuse near the battery as shown.
• Connect the lead wire (purchased separately) through which power is supplied directly to the
battery’s “ª” terminal only after all the other connections have been made.
∗ Do not connect the “·” terminals of the speakers to each other.
∗ Do not connect the “·” terminals of the speakers to the metal body or chassis.
• Cover the unused terminals with insulating tape to prevent them from short circuiting.
• When an extension lead is used, it should be as thick and short as possible; connect it firmly
with insulating tape.
The lead wire connected to the + B terminal of this unit should have a cross-section of more
than 5 mm2. Be sure to use a ring terminal (optional) for secure connection.
• Be sure to leave an appropriate space between the antenna (aerial) and the wires of this unit.
•
When replacing the fuse, only use a 25 A fuse for KS-AX3500 and 30 A fuse for KS-AX3300.
• Do not let pebbles, sand or metallic objects get inside the unit.
To keep the heat dissipation mechanism running effectively, wipe the accumulated dust off periodically.
• If you have any questions regarding the thickness of the power cord, etc., consult your nearest
“JVC IN-CAR ENTERTAINMENT” car audio dealer.
•
When connecting a unit without a remote lead (.), connect to the accessory circuit of the car
which is activated by the ignition switch. In this case, noise may occur when the car receiver is
turned on or off. To avoid this noise, do not turn on or off the car receiver itself.You can turn on or
off the car receiver along with the on/off operation of the ignition switch.
• Listening to the tape, radio, CD or MD, etc. with the volume on loud for a long period of time will
exhaust the battery, while the engine is turned off or while the engine is idling.
DO NOT disassemble the units since there are no user serviceable parts inside.
If you use JVC car receiver with a remote lead (∫), connect to the REM terminal on this unit.
For Customer Use:
Enter below the Model No. and Serial No. which
If the POWER/PROTECTOR lamp lights in red, it indicates incorrect speaker wiring or
connections. In normal status, the POWER/PROTECTOR lamp lights in green. Make sure to
correct speaker wiring and other connections.
Model No.
are located on the top or bottom of the cabinet.
Serial No.
Retain this information for future reference.
INSTALLATION
CONTROLS
The following illustration shows a typical installation. However, you should make adjustments
corresponding to your specific car. If you have any questions or require information regarding
installation kits, consult your “JVC IN-CAR ENTERTAINMENT” car audio dealer or a company
supplying kits.
KS-AX3500
KS-AX3300
Å Crossover filter switch
OFF: Normally, set to this position. (Preset to this position at the factory.)
ON: (For LPF switch) Set to this position when you want to turn on the LPF (Low-pass
filter) switch.You can use the following terminals for a subwoofer
system.
Å Mount on a firm surface, such as in the trunk room or under the front seat.
• Since heat is generated in this unit, do not mount near inflammable objects. In addition,
mount in an area that will not prevent the unit from dissipating heat.
• Do not mount the unit in the places subject to heat such as near a radiator, in a glove
compartment or in insulated areas such as under a car mat that will prevent the unit from
dissipating heat.
KS-AX3500: REAR SPEAKER OUTPUT
KS-AX3300: SPEAKER OUTPUT
(For HPF switch—only for KS-AX3500)
Set to this position when you want to turn on the HPF (High-pass
filter) switch. The low frequency signals are not applied to the left/
right speaker when a subwoofer is connected.
ı When mounting this unit, be sure to use the screws provided. If any other screws are used,
there is a risk of loosening the unit or damaging parts inside it.
ı Input LEVEL controller
The input level can be adjusted with this control when this unit is connected to other source
equipments. Turn it in the clockwise direction when the output level of the car audio seems low.
TERMINAL CONNECTIONS
When making the terminal connections…
SPEAKER SYSTEMS
Properly fix the terminal with the screw provided by turning it in the
direction as illustrated.
This amplifier provides two types of speaker connections: Normal mode and Bridge mode.You
can choose either type of connections depending on the speakers configuration equipped on
your car.
Note
Make sure to comply with the following notes:
When you tighten the screw, make sure that the screw is securely fixed in
place to prevent disconnection of the terminal. Avoid over-tightening as it
may cause damage to the screw or its head slot.
• Be sure not to connect the “·” terminals of the speakers to a common point.
• If the ground wire is common to both left/right and front/rear speaker wirings, this unit cannot be
used. Always use the independent lead wires for the speakers to be used. In this case, redo the
wirings.
• Use the speakers with an impedance of 2 Ω to 8 Ω (4 Ω to 8 Ω: when used in Bridge mode).
• Use the speakers which have sufficient power to the unit.
1
|