ENGLISH
VIDEO CASSETTE RECORDER
HR-S5960E
HR-S5961E
HR-S5962E
HR-S5963E
INSTRUCTIONS
LPT0751-001B
Printed in Germany
0203-AH-PJ-JVE
COPYRIGHT © 2003 VICTOR COMPANY OF JAPAN, LTD.
WARNING
SAFETY FIRST............................................................................... 1
Buttons, Connectors and Indicators ................................................ 3
Basic Connections.......................................................................... 4
Initial Settings.............................................................................. 4
Auto Set Up............................................................................ 4
Language Set .......................................................................... 5
There are two different types of SECAM colour systems:
SECAM-L, used in FRANCE (also called SECAM-West), and
SECAM-B, used in Eastern European countries (also called
SECAM-East).
1. This recorder can also receive SECAM-B colour television
signals for recording and playback.
2. Recordings made of SECAM-B television signals produce
monochrome pictures if played back on a video recorder of
SECAM-L standard, or do not produce normal colour
pictures if played back on aPAL video recorder with
SECAM-B system incorporated (even if the TV set is SECAM-
compatible).
3. SECAM-L prerecorded cassettes or recordings made with a
SECAM-L video recorder produce monochrome pictures
when played back with this recorder.
Playback ...................................................................................... 5
Recording..................................................................................... 7
Timer Recording............................................................................ 8
SHOWVIEW® Timer Programming............................................. 8
Express Timer Programming.................................................... 9
Checking, cancelling or changing programme settings ........... 9
Automatic Satellite Programme Recording.............................. 9
Editing ....................................................................................... 10
Editing with another video recorder or a camcorder ............. 10
Output/Input Set........................................................................ 10
L-1 OUTPUT Setting: ........................................................... 10
L-2 SELECT and L-2 INPUT Setting: ...................................... 10
4. This recorder cannot be used for the SECAM-L standard. Use
a SECAM-L recorder to record SECAM-L signals.
IMPORTANT
Ⅲ Please read the various precautions on pages 1 and 2 before
installing or operating the recorder.
Ⅲ It should be noted that it may be unlawful to re-record pre-
recorded tapes, records, or discs without the consent of the
owner of copyright in the sound or video recording, broadcast
or cable programme and in any literary, dramatic, musical, or
artistic work embodied therein.
System Connections .................................................................... 11
Connecting to a satellite receiver.......................................... 11
Connecting/Using a decoder ................................................ 11
Connecting/Using a stereo system ........................................ 11
Subsidiary Settings..................................................................... 11
Mode Set.............................................................................. 11
Clock Set.............................................................................. 13
Tuner Set .............................................................................. 13
Video Channel Set................................................................ 15
For Italy:
“It is declared that this product, brand JVC, conforms to the
Ministry Decree n. 548 of 28 Aug.’95 published in the Official
Gazette of the Italian Republic n. 301 of 28 Dec.’95”
Specifications.............................................................................. 16
The STANDBY/ON 1 button does not completely shut off
mains power from the unit, but switches operating current on
and off. “`” shows electrical power standby and “ ! ” shows
ON.
SAFETY FIRST
Safety Precautions
The rating plate and the safety caution are on the rear of the unit.
Video tapes recorded with this video recorder in the LP (Long
Play) mode cannot be played back on a single-speed video
recorder.
WARNING:DANGEROUS VOLTAGE INSIDE
WARNING:TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
CAUTION
Caution on Replaceable lithium battery
The battery used in this device may present a fire or chemical
burn hazard if mistreated. Do not recharge, disassemble, heat
above 100°C or incinerate.
Replace battery with CR2032. Panasonic (Matsushita Electric)
or Maxell is recommended.
Ⅲ When you are not using the recorder for a long period of
time, it is recommended that you disconnect the power cord
from the mains outlet.
Ⅲ Dangerous voltage inside. Refer internal servicing to qualified
service personnel. To prevent electric shock or fire hazard,
remove the power cord from the mains outlet prior to
connecting or disconnecting any signal lead or aerial.
Danger of explosion or Risk of fire if the battery is incorrectly
replaced.
Ⅲ Dispose of used battery promptly.
Ⅲ Keep away from children.
Ⅲ Do not disassemble and do not dispose of in fire.
— 1 —
Remote control
Buttons, Connectors and Indicators
Front Panel
Pause 9 [SAT#]
Record7 Stop/Eject
0
number keys
Cassette loading slot
Rewind
3
Play 4
PR+/–
Fast
Forward
5
Infrared beam
receiving window
Display panel
Timer mode indicator
VCR indicator
S-VHS indicator
REVIEW indicator
Play indicator
SAT# indicator
Record
indicator
Channel and
auxiliary input/
Clock time*
Counter/Remain display**
* PDC recording is not possible in Central and Eastern Europe.
* Each time you press – –:– –, the display panel shows the channel
number and the clock time alternatively.
**The counter can display up to +/– “19:59:59”. If the playback or
recording time exceeds this limit the display starts to count from
“0:00:00”.
On-screen display
“ON” (੬ 12), you can see the current recorder status on the
screen. To clear the on-screen display, press
If you press (OK) on the remote control when “O.S.D.” is set to
(OK) again.
The indications are not recorded even if the recorder is in the
recording mode.
Rear Panel
Mains power cord
S-VHS ET : OFF
A Recorder operation mode
B Tape speed
C Tape direction
D Time counter
E Tape remaining time
F Audio mode
G Tape position*
* The position of “ q” in relation to “0” (Beginning) or “+” (End) shows
the current position on the tape.
H VPS/PDC* indicator
* PDC recording is not possible in Central and Eastern Europe.
I Type of broadcast
J Current day/month/year
K Clock
L Channel and auxiliary input
M Cassette loaded mark
N S-VHS ET indicator
— 3 —
Basic Connections
Initial Settings
After the 1 is pressed for the first time to power on the recorder,
A Check contents
the recorder starts Auto Set Up.
Make sure the package contains all of the accessories listed in
Before starting:
“Specifications” (੬ 16).
● Perform “Basic Connections”.
● Set the TV to its AV mode (with AV connection) or UHF
channel 36 (with RF connection).
B Situate recorder
Place the recorder on a stable, horizontal surface.
C Connect recorder to TV
Auto Set Up
— Auto Channel Set/Auto Clock Set*/Auto Guide Program
Number Set
Aerial connector
Back of TV
* If you select a country in Central or Eastern Europe, set the clock
manually (੬ 13).
ATTENTION:
While performing Auto Set Up for the first time,
● do NOT disconnect the recorder from the power supply (AC)
● do NOT press any button unless instructed
● ensure that Auto Set Up is not interrupted while the operation
is still in progress
TV aerial cable
A Turn on recorder
Press 1. The Country Set screen appears
on the screen.
21-pin SCART
connector
● If you have connected your TV to the
recorder with RF connection and the on-
screen display appearing on UHF
channel 36 looks distorted, perform
“Video Channel Set” (੬ 15).
21-pin SCART cable
(not provided)
RF cable
(provided)
B Select your country
Press rt to place the pointer next to your country, then press
OK. The language is automatically selected for the on-screen
display depending on the country you have selected.
● If you have selected BELGIUM or SUISSE, the Language Set
screen appears. Press rt to place the pointer next to the
desired language, then press OK.
Mains power cord
ANT. IN
● If you have selected MAGYARORSZÁG,
CESKÁ REPUBLIKA, POLSKA or OTHER
EASTERN EUROPE, the Clock Set screen
appears. Press rt until the desired time
appears, then press OK or e. Set the date
and year in the same way. (Holding rt
Back of recorder
changes the time in 30-minute intervals,
L-1 IN/OUT
RF OUT
or changes the date in 15-day intervals.)
Then press MENU.
Mains outlet
C Perform Auto Set Up
“Auto” blinks on the front display
panel; do NOT press any button on
the recorder or remote control until
the front display panel shows clock
time, “1” or “– –:– –”.
AUTO SET
RF Connection
PLEASE WAIT
A Disconnect the TV aerial cable from the TV.
B Connect the TV aerial cable to the ANT. IN connector on the
rear of the recorder.
C Connect the provided RF cable between the RF OUT
connector on the rear of the recorder and the TV’s aerial
connector.
● If you are using the on-screen
display, the AUTO SET screen will
appear. As Auto Set Up progresses,
End
Beginning
the “q” mark on the TV screen moves from left to right.
AV Connection
D Confirm/Set video channel
With RF connection
If your TV is equipped with a 21-pin SCART connector, perform
AV connection to improve picture quality during tape playback.
A Connect the aerial, recorder and TV as shown in the
illustration.
The video channel that is shown on the
display panel is your video channel. Press
OK.
● If you have selected MAGYARORSZÁG,
CESKÁ REPUBLIKA, POLSKA or OTHER
EASTERN EUROPE in step 2, “2”
appears instead of “1”.
B Connect an optional 21-pin SCART cable between the L-1 IN/
OUT connector on the rear of the recorder and the TV’s 21-pin
SCART connector.
D Connect recorder to mains
Plug the mains power cord into a mains outlet.
● To view picture signals from the recorder, set your TV to the
video channel.
— 4 —
With AV connection
Press PR – until the display panel shows
“1 – –”(or“2 – –”). Nowthevideochannel
is set to off. Then press OK.
Playback
● To view picture signals from the recorder, set your TV to its AV
mode.
Basic Playback
Turn on the TV and select the video channel or AV mode.
E Check results
If both Auto Channel Set and Clock Set
A Load a cassette
have been performed successfully, the
correct current time is displayed.
Turn on the TV and select its video channel
or AV mode. Then make sure that all necessary stations have been
stored in the recorder’s memory by using the PR button(s).
Make sure the window side is
up, the rear label side is facing
you and the arrow on the front of
the cassette is pointing towards
the recorder.
If Auto Channel Set has succeeded but
Clock Set has not, “1” is displayed.
● Do not apply too much pressure when inserting.
● The recorder turns on, and the counter is reset, automatically.
● If the cassette’s record safety tab has been removed, playback
begins automatically.
A Turn on the TV and select its video
channel or AV mode. Then make sure that all
necessary stations have been stored in the recorder’s memory by
using the PR button(s).
B Start playback
Press 4.
The S-VHS indicator lights up when you play back a tape recorded
in S-VHS mode or in S-VHS ET mode (੬ 8).
B Perform “Clock Set” (੬ 13).
If both Auto Channel Set and Clock Set
have failed, “– –:– –” is displayed.
Makesurethecablesareconnectedproperly.
Turn off the recorder once, then turn the
recorder back on again. The Country Set screen appears on the
screen. Perform “Auto Set Up” again.
During playback
Stop playback
Press 8 on the remote
control.
OR Press 0 on the recorder.
Language Set
Pause playback and view still picture
You can change the language setting manually as required.
Press 9.
A Access Main Menu screen, then Auto
● Press 4 to resume normal playback.
● If there is vertical jitter, press PR r/t on the remote control or
PR+/– on the recorder to correct the picture.
Channel Set screen
Press MENU. Press rt to place the
OUTPUT/INPUT SET
CLOCK SET
pointer next to “AUTO CH SET”, then press
OK or e.
Pause and Frame-by-Frame playback
Press 9 to pause, then press w or e (or 9) repeatedly.
● Press 4 to resume normal playback.
B Select your country
Press rt to place the pointer next to your
Picture Search
country, then press OK or e.
Press 3 or 5. Press 3 or 5 again to perform high-
speed search.
● Each time you press 3 or 5, the search speed changes
between low-speed and high-speed.
● Press 4 to resume normal playback.
C Select language
Press rt to place the pointer next to the desired language.
● You do not have to press OK; pressing OK starts Auto Channel
Set.
Variable Speed Search (including slow-motion)
D Return to normal screen
Press MENU.
Press w or e repeatedly.
● Press 4 to resume normal playback.
● Each time you press w or e, the playback speed changes. To
decrease the speed during picture search, press the opposite
direction button repeatedly.
● During still picture, press and hold e to start forward (or w to
start reverse) slow motion playback. When you release the
button, still picture resumes. During still picture, holding 9 for
more than 2 seconds also starts forward slow motion playback.
If you press 9 again, still picture resumes.
● During slow motion playback, some noise may appear on the
TV screen. Press PR r/t on the remote control or PR+/– on
the recorder to eliminate the noise.
Forward
Reverse
Reverse
slow
motion
1 step
Reverse
search
3 steps
Slow
motion
1 step
Forward
search
4 steps
Reverse
play
Normal
play
— 5 —
Playing back tape repeatedly (100 times)
— Repeat Playback
When the tape is not running
Rewind/fast-forward
Press 3 or 5.
During playback, press and hold 4 for more than 5 seconds. “$”
on the display panel starts blinking slowly. To stop playback, press
8 on the remote control or 0 on the recorder.
Eject the cassette
Press 0.
NOTE:
● You can also eject the cassette when the recorder is turned off.
Pressing 4, 3, 5 or 9 also stops Repeat Playback.
Turn off the recorder
Press 1.
Locating beginning of recordings
— Index Search
Index codes are placed on the tape at the
beginning of each recording when
recording on this recorder.
ATTENTION:
In the search, still, slow-motion or frame-by-frame playback
mode,
● the picture will be distorted
● the noise bars will appear
● there will be a loss of color with an LP-recorded tape
A While the tape is not running, press w or
e (2 or 6 ) to start search.
B To access a recording of 2 to 9 index
codes away, press w or e (2 or 6 )
repeatedly until the correct number is displayed on the screen
(only if “O.S.D.” is set to “ON” (੬ 12)).
Example:
To locate the beginning of B from
the current position, press w
twice.
Playback Features
Adjusting tracking condition
Current position
Automatic tracking adjustment
When a new cassette is loaded, the recorder enters the automatic
tracking mode.
To locate the beginning of D from
the current position, press e
once.
Manual tracking adjustment
If automatic tracking cannot eliminate noises well during
playback, adjust the tracking manually.
● Playback begins automatically
when the desired recording is
located.
Index number
On the remote control:
A Press p to activate manual tracking.
B Press PR r or t to eliminate the noises. Press it briefly for a
fine adjustment, or press and hold for a coarse adjustment.
● Press p again to reactivate automatic tracking.
Locating beginning of timer recordings
— Instant Review
After ensuring that the recorder is turned off and that the timer
mode is disengaged, press REVIEW.
Selecting Soundtrack
● The recorder turns on, and rewinds to the index code indicating
the beginning of the last timer-recorded programme, then begins
playback automatically.
Your recorder is capable of recording three soundtracks (HIFI L j,
HIFI h R and NORM) and plays back the one you select.
Pressing AUDIO changes the soundtrack as follows:
● You can access a programme as far as
HIFI L j h R
HIFI L j
HIFI h R
: For Hi-Fi stereo tapes
9 index codes away from the current
: For main audio of Bilingual tapes
: For sub audio of Bilingual tapes
: For audio-dubbed tapes
tape position. For example, if you have
timer-recorded 3 programmes, the
NORM
REVIEW indicator “( )” and “3” blink. To watch the first of the
3 programmes, press REVIEW three times.
HI FI NORM
: For audio-dubbed tapes
● The number of recorded programmes is not displayed on the
display panel after Automatic Satellite Programme Recording.
● The Instant Review function can also operate if the recorder is
turned on.
NOTE:
Set “O.S.D.” to “ON” to display the indications on the screen.
(੬ 12)
Automatic operations after rewinding
— Next Function Memory
Skipping unwanted portions
— Skip Search
The Next Function Memory “tells” the recorder what to do after
rewinding. Ensure that the recorder is in stop mode.
● For Automatic Playback Start
Press 30 SEC
once to 4 times during playback. Each press
initiates a 30-second period of high-speed playback (up to
2 minutes). When the specified portion of the tape is skipped,
normal playback resumes automatically. To return to normal
playback during Skip Search, press 4.
Press 3, then press 4 within 2 seconds.
● For Automatic Power Off
Press 3, then press 1 within 2 seconds.
● For Automatic Timer Standby
Press 3, then press # within 2 seconds.
NOTE:
It is not possible to select the Automatic Timer Standby function if
the cassette’s record safety tab is removed.
— 6 —
Tape Remaining Time/Time Counter
Recording
Press – –:– – to display the tape remaining time and time counter
on the screen and the front display panel. To reset the time
counter, press 0000.
Accidental erasure prevention
To prevent accidental recording on a
recorded cassette, remove its record
safety tab. To record on it later, cover
the hole with adhesive tape.
● The front display panel shows the counter reading with “:” lit.
● The front display panel shows the tape remaining time with “:”
blinking.
Record safety tab
NOTES:
● Set “O.S.D.” to “ON” to display the indications on the screen.
(੬ 12)
Basic Recording
● Depending on the type of tape used, the tape remaining time
may not appear right away, or is not correct. “– –:– –” may
sometimes appear, or the display may blink on occasion.
Turn on the TV and select the video channel orAV mode.
A Load a cassette
Watching one programme while recording another
Make sure the record safety tab is intact. If not, cover the hole with
adhesive tape before inserting the cassette.
If your recorder is connected to the TV via the AV connection
(੬ 4), press TV/VCR. The recorder’s VCR indicator and the TV
broadcast being recorded disappear. Once recording is in
progress, all you need to do is to set the channel controls on the
TV for the station you wish to view.
● The recorder turns on, and the counter is reset, automatically.
B Select recording channel
PressPRr/torthenumberkeysontheremotecontrolorPR+/–
ontherecorder.
● The programme selected with the TV’s channel controls appears
on the screen, while the one selected with the PR r/t on the
remote control or PR+/– on the recorder is recorded on the
tape.
● If a decoder is connected to the recorder, you can select a
scrambled channel as well with the TV channel controls.
● Youcanselect channelinthestopmode orrecordingpausemode.
C Set tape speed
Press SP/LP (p). The current setting for the tape speed appears
on the display panel and the screen for about 5 seconds. Press SP/
LP (p) again to change the setting while tape speed is displayed.
D Start recording
Specifying recording length
On the recorder, press 7. Or on the remote control, while holding
— Instant Timer Recording (ITR)
7, press 4.
During recording, press 7 on the recorder repeatedly until the
desired recording length appears on the display panel. “⅜” on the
display panel starts blinking.
● Each time you press the button, recording length increases in
30-minute intervals (up to 6 hours).
● The recorder turns off after recording is finished.
● To cancel an ITR, press 8 on the remote control or 0 on the
recorder.
NOTES:
● If “B.E.S.T.” is set to “ON” (੬ 11) (default setting), the recorder
takes about 7 seconds to assess the quality of the tape in use, then
recording begins with the picture level optimized.
● If the tape reaches its end during recording, the recording stops
and “ ⅜” and “ $” on the display panel blink. Press 0 on
the recorder to eject the cassette or press 3 to rewind the
tape.
Receiving stereo and bilingual programmes
During recording
Pause recording
Your recorder is equipped with a Sound-Multiplex decoder (A2)
and a Digital stereo sound decoder (NICAM), making reception of
stereo and bilingual broadcasts possible.
Press 9.
● Press 4 to resume recording.
● You can select channel in the recording pause mode.
When the channel is changed, the type of broadcast being
received will be displayed on the screen for a few seconds.
Stop recording
Type of broadcast being received
On-screen display
Press 8 on the remote
control.
OR Press 0 on the recorder.
A2 Stereo
A2 Bilingual
Regular Monaural
NICAM Stereo
NICAM Bilingual
NICAM Monaural
ST
BIL.
(none)
ST NICAM
BIL. NICAM
NICAM
Recording Features
Recording Resume Function
● To listen to a stereo programme, press AUDIO until
“HIFI L j h R” appears on the screen.
● To listen to a bilingual programme, press AUDIO until
“HIFI L j” or “HIFI h R” appears on the screen.
● To listen to the standard (regular monaural) audio while
receiving a NICAM broadcast, press AUDIO until “NORM”
appears on the screen.
If there is a power outage during recording (or Instant Timer
Recording, or timer recording), the recording will resume
automatically when the power is restored to the recorder. (No
setting is required for this function.)
NOTE:
If a power outage exceed the recorder’s memory backup time,
Recording Resume Function does not work.
NOTE:
Set “O.S.D.” to “ON” to display the indications on the screen.
(੬ 12)
— 7 —
To record stereo and bilingual programmes (A2)
● Stereo programmes are automatically recorded in stereo on the
Hi-Fi audio track (with the normal audio track recording mixed
L and R channel sound).
● Bilingual programmes are automatically recorded in bilingual
on the Hi-Fi audio track. The main soundtrack is recorded on
the normal audio track.
To record NICAM stereo and bilingual programmes
The NICAM audio programme is recorded on the Hi-Fi audio
track, and the standard audio programme on the normal audio
track.
NOTES:
● If the quality of stereo sound being received is poor, the
broadcast may be received in monaural with better quality.
● Before playing back a programme recorded in stereo, or a
bilingual programme, refer to “Selecting Soundtrack” (੬ 6).
S-VHS (Super VHS), S-VHS ET or VHS Recording
Mode
This VCR can record in S-VHS (Super VHS), S-VHS ET or VHS.
● To record in S-VHS:
Set “S-VHS” to “ON” (੬ 12). Then, insert a cassette marked
“S-VHS”. The S-VHS indicator lights up on the display panel.
The S-VHS recording mode is selected.
SHOWVIEW® Timer Programming
● To record in S-VHS ET on a VHS cassette:
Set “S-VHS ET” to “ON” (੬ 11). Then, insert a cassette marked
“VHS”. The S-VHS indicator lights up on the display panel.
● To record in VHS:
The SHOWVIEW numbers are the numbers next to the programme
in most TV listing.
A Press PROG to access the Timer Programming Set screen.
Insert a cassette marked “VHS”.
B Press rt to place the pointer next to
“SHOWVIEW“, then press OK or e. The
SHOWVIEW NO. screen appears.
Set “S-VHS ET” to “OFF” (੬ 11).
● To record in VHS on a S-VHS cassette:
Insert a cassette marked “S-VHS”. The S-VHS indicator lights up
on the display panel. Then, set “S-VHS” to “OFF” (੬ 12). The
S-VHS indicator goes off.
The VHS recording mode is selected.
NOTE:
When playing back a tape that has been recorded in S-VHS or
S-VHS ET, the S-VHS indicator lights up on the display panel
regardless of the “S-VHS ET” (੬ 11) or “S-VHS MODE” (੬ 12)
setting.
C Press the appropriate number keys to
input the SHOWVIEW number, then press
OK. The SHOWVIEW program screen
appears.
● If the number you entered is invalid,
“ERROR” appears on the screen. Press
& and input a valid SHOWVIEW
Timer Recording
Up to 8 timer recording programmes can be made.
number.
● Make sure the channel position
number you wish to record is displayed; if “TV PROG” displays
“– –”, set the channel position number correctly. Press PR r/t
to input the channel position number on which your recorder
receives the station. Then press OK.
Before starting:
● Set the clock properly. (੬ 13)
● Set “COLOUR SYSTEM” to the appropriate mode. (੬ 12)
● Load a cassette with the record safety tab intact.
● To set the tape speed, press SP/LP (p).
● To set the VPS/PDC mode, press VPS/PDC (number key “7”).
● To change the stop time, press STOP
and/or “5”).
NOTES:
/
(number keys “2”
● PDC recording is not possible in Central and Eastern Europe.
● If all the 8 programmes have already been set, “PROGRAM
FULL” appears on the screen.
● To timer-record daily (Monday–Friday) or weekly serials, press
DAILY (number key “8”) or WEEKLY (number key “9”). Pressing
the button again makes the “DAILY” or “WEEKLY” display
disappear.
● If the clock is not set, “CLOCK MUST BE SET” appears on the
screen.
● If there is a conflict in the timer schedule and one programme
overlaps with another, the programme starting earlier or
programme with the lower programme number will be
recorded.
● To change the channel position number, press PR r/t.
D Press OK or PROG.
E Press #. The recorder turns off automatically and “#” is
displayed on the display panel.
● After timer recording is completed, the recorder turns off
automatically.
To timer-record a satellite broadcast using the SHOWVIEW system:
A Set “L-2 SELECT” to “A/V” (੬ 10).
B Perform steps 1 – 5.
C Set the satellite receiver to the appropriate channel before the
selected programme begins.
D Leave the satellite receiver’s power on.
● If the tape reaches its end during timer recordings, the recording
stops and “ #”, “ ⅜” and “ $” on the display panel blink. Press
# to disengage timer, then press 0 on the recorder to eject
the cassette or press 1 then press 3 to rewind the tape.
● You can programme the timer recording while a regular
recording is in progress; the menu screens will not be recorded.
— 8 —
Express Timer Programming
Checking, cancelling or changing programme
settings
A Disengage timer recording standby mode
Press #, then press 1.
● When “AUTO TIMER” is set to “ON” (੬ 12), press only 1.
A Press PROG to access the Timer Programming Set screen.
B Press rt to place the pointer (highlighted bar) next to
“EXPRESS PROGRAMMING”, then press OK or e. The program
screen appears.
C Press START
/
(number keys “1”
B Access Program Check screen
Press ".
and/or “4”), STOP
and/or “5”), DATE
and/or “6”) or PR
/
(number keys “2”
/
(number keys “3”
repeatedly to enter
/
the start time, stop time, date or channel.
● Press and hold START
/
or STOP
/
to increase the time in 30-minute
intervals.
● To set the tape speed, press SP/LP (p).
● To set the VPS/PDC mode, press VPS/PDC (number key “7”).
● To timer-record daily (Monday–Friday) or weekly serials, press
DAILY (number key “8”) or WEEKLY (number key “9”). Pressing
the button again makes the “DAILY” or “WEEKLY” display
disappear.
C Access Program screen
Press " again. Each time you press ",
the next programme’s screen appears.
D Cancel or change programme setting
To cancel a programme, press &.
D Press OK or PROG.
To change a programme, press the
appropriate button: START
keys “1” and/or “4”), STOP
/
(number
(number keys “2” and/or “5”),
E Press #. The recorder turns off automatically and “#” is
displayed on the display panel.
/
DATE
/
(number keys “3” and/or “6”), DAILY (number key
To timer-record a satellite broadcast using Express Timer
Programming:
“8”), WEEKLY (number key “9”), PR
/
, VPS/PDC (number key
“7”) and/or SP/LP (p).
A Set “L-2 SELECT” to “A/V” (੬ 10).
B Perform steps 1 – 5.
C Set the satellite receiver to the appropriate channel before the
selected programme begins.
D Leave the satellite receiver’s power on.
E Return to normal screen
Press " repeatedly until no Program screen is shown.
F Re-engage timer recording standby mode
Press #. The recorder turns off automatically and “#” is displayed
on the display panel.
● When “AUTO TIMER” is set to “ON” (੬ 12), the timer
recording standby mode automatically resumes when you turn
off the recorder.
VPS/PDC Recording
Now available from some TV stations, PDC (Programme Delivery
Control) and VPS (Video Programme System) are service designed
to assure safe, accurate timer recording. With this system, your
recorder will start and stop recording when the preset TV
programmes actually start and end — even if the broadcast time of
a preset TV programme is changed.
Automatic Satellite Programme Recording
You can automatically record a satellite programme which is
timer-programmed on your satellite receiver.
NOTE:
When you use ExpressTimer Programming, set the start time (VPS
or PDC time) exactly as advertised in the TV listing.
A Connect a satellite receiver to the L-2 IN/DECODER connector
on the rear panel.
How to check if the station being received transmits a VPS/PDC
signal (Excepting in Central and Eastern Europe)
A Press – –:– – until the channel position appears on the display
panel.
B Hold down 9 on the remote control for about 5 seconds.
“VPS/PDC” appears blinking on the screen.
If a VPS/PDC signal is detected from the station, “VPS/PDC” will
stop blinking.
If no VPS/PDC signal is detected from the station, “VPS/PDC” will
blink at a slower rate.
C Press – –:– – or 9 on the remote control again to return to
normal screen.
B Set timer programme on satellite receiver referring to its
instruction manual.
C Load a cassette with the record safety tab intact.
D Set “L-2 SELECT” to “A/V” or “SAT”. (੬ 10)
E To set the tape speed, press SP/LP (p). The current setting for
the tape speed appears on the display panel or the screen for
about 5 seconds. Press SP/LP (p) again to change the setting
while tape speed is displayed.
F Press SAT# for more than 2 seconds. The recorder turns off
automatically and enter the Automatic Satellite Programme
Recording mode (the # and indicators light up). When signals
come into the recorder from the satellite receiver, the recorder
starts recording (the # and indicators blink). The recorder stops
recording and turns off when signals stop coming in.
NOTES:
● Be sure not to turn on the satellite receiver before the
programme starts broadcasting; otherwise, the recorder starts
recording when the satellite receiver is turned on.
● To disengage the Automatic Satellite Programme Recording
mode, press SAT# (the # and indicators go off).
● Depending on the type of satellite receiver, Automatic Satellite
Programme Recording may not be compatible.
● B.E.S.T. does not work in the Automatic Satellite Programme
Recording mode.
● Power Save mode does not work in the Automatic Satellite
Programme Recording mode.
● Just Clock does not work in the Automatic Satellite Programme
Recording mode.
— 9 —
Editing
Output/Input Set
Editing with another video recorder or a
camcorder
L-1 OUTPUT Setting:
The L-1 IN/OUT connector accepts only a composite signal
(regular video signal) and delivers either a composite signal
(regular video signal) or a Y/C signal (a signal in which the
luminance and chrominance signals are separated). Set “L-1
OUTPUT” to the appropriate mode depending on the type of
appliance connected to the recorder’s L-1 IN/OUT connector.
You can use your recorder as the source player or the recording
deck. You can use a camcorder as the source player and your
recorder as the recording deck. Refer also to the other
components’ instruction manuals for connection and its
operations.
A Make connections
L-2 SELECT and L-2 INPUT Setting:
Connection with another video recorder
The L-2 IN/DECODER connector accepts either a composite
signal (regular video signal) or a Y/C signal (a signal in which the
luminance and chrominance signals are separated). Set “L-2
SELECT” to the appropritate mode depending on the type of
appliance connected to the recorder’s L-2 IN/DECODER
connector. Set “L-2 INPUT” to the appropriate mode depending
on the output signals of the connected appliance.
Your recorder
L-2 IN/DECODER or
L-1 IN/OUT
To L1 IN/OUT
NOTES:
● If you have a satellite receiver or a decoder connected to the L-2
IN/DECODER connector, be sure to set “L-2 SELECT” back to
appropriate mode after editing.
● If you are not connecting a satellite receiver or a decoder to the
L-2 IN/DECODER connector, leave “L-2 SELECT” set to “A/V”.
● When “L-2 SELECT” is set to “SAT”, “SAT” or “SAt” appears on
TV screen or front display panel instead of “L-2” or “L2”.
● If “L-2 SELECT” is set to “DECODER”, it is impossible to set “L-2
INPUT” to “S-VIDEO”.
When using your
When using your
recorder as the source
player, connect its L-1
IN/OUT connector to
the recording deck.
recorder as the
21-pin
SCART cable
(not
recording deck,
connect its L-2 IN/
DECODER or L-1 IN/
OUT connector to the
source player.
provided)
● If “L-1 OUTPUT” is set to “S-VIDEO”, it is impossible to set “L-2
SELECT” to “DECODER”.
A Access the Main Menu, then Output/Input Set screen
Press MENU. Press rt to move the
highlight bar (pointer) to “OUTPUT/
INPUT SET”, then press OK or e.
Another recorder
● If another recorder is compatible with the Y/C signal…
… When using your recorder as the source player, set “L-1
OUTPUT” to “S-VIDEO” in “Output/Input Set”.
… When using your recorder as the recording deck, set “L-2
INPUT” to “S-VIDEO” in “Output/Input Set”.
Connection with a camcorder
Connect the camcorder’s AUDIO/VIDEO OUT connectors to the
recorder’s L-1 IN/OUT or L-2 IN/DECODER connector via a cable
adapter.
B Select the output or input mode for
L-1 OUTPUT
VIDEO
the connectors
L-2 SELECT
L-2 INPUT
A/V
Press rt to move the highlight bar
(pointer) to the desired mode. Then,
press OK or e to select the appropriate
setting. The default setting is bold in the
table below.
VIDEO
B Load cassettes
Insert the playback cassette into the source player and the cassette
to be recorded on into the recording deck.
Press MENU to return to normal screen.
C Select input mode on recording deck
Select the correct external input on the recording deck. On this
Ⅵ L-1 OUTPUT — VIDEO / S-VIDEO
VIDEO: If a connected appliance’s input is compatible only with
regular video signals, set to “VIDEO”.
S-VIDEO: If a connected appliance’s input is compatible with Y/C
signals, set to “S-VIDEO”. You can obtain high-quality S-VHS
picture. (For connection, be sure to use a 21-pin SCART cable that
is compatible with the Y/C signal.)
recorder, press AUX and/or PR
r
/t
on the remote control or PR+/–
on the recorder.
Select “L-1” for the L-1 IN/OUT connector, or “L-2” for the L-2 IN/
DECODER connector.
● When using the L-2 IN/DECODER connector, set “L-2 SELECT”
to “A/V” in “Output/Input Set”.
D Select edit mode
Select the appropriate edit mode for the components if such a
mode is equipped.
● On this recorder, set “PICTURE CONTROL” to “EDIT”. (੬ 12)
Ⅵ L-2 SELECT — A/V / DECODER / SAT
A/V: To use this recorder as the recording deck with the player
connected to the L-2 IN/DECODER connector, or to use the
satellite receiver connected to the L-2 IN/DECODER connector.
DECODER: To use a decoder connected to the L-2 IN/DECODER
connector.
E Start playback
Engage the Play mode of the source player.
F Start recording
SAT: To view a satellite programme with the TV set while the
recorder is turned off. (੬ 11)
Engage the Record mode of the recording deck.
— 10 —
Ⅵ L-2 INPUT — VIDEO / S-VIDEO
VIDEO: If a connected appliance’s output is compatible only with
regular video signals, set to “VIDEO”.
Subsidiary Settings
S-VIDEO: If a connected appliance’s output is compatible with
Y/C signals, set to “S-VIDEO”. You can obtain high-quality S-VHS
picture. (For connection, be sure to use a 21-pin SCART cable that
is compatible with the Y/C signal.)
Mode Set
You can change various mode settings.
Turn on the recorder and the TV, and set your TV to its AV mode
or video channel.
System Connections
A Access Main Menu screen, then Mode Set screen
Press MENU. Press rt to place the
pointer next to “MODE SET”, then press
OK or e.
NOTE:
When you select a country in Central or Eastern Europe for
country setting, you cannot use decoder with this recorder.
OUTPUT/INPUT SET
CLOCK SET
B Select mode
Connecting to a satellite receiver
Press rt to place the pointer next to the
Connect the decoder to the satellite receiver’s connector if you
have a decoder, L-1 IN/OUT connector to TV’s connector, and
L-2 IN/DECODER connector to the satellite receiver’s connector.
Then connect the satellite receiver and TV.
item you want to set.
● Set “L-2 SELECT” to “A/V”. (੬ 10)
● To record a programme via the satellite receiver, set the input
mode to “L-2” by pressing AUX or PR r/t on the remote
control or PR+/– on the recorder.
● To receive a scrambled broadcast, descramble the signal with
the satellite receiver.
● For details, refer to the instruction manual for the satellite
receiver and decoder.
C Change setting
Press OK or e. The default setting is bold in the following table.
Press MENU to return to normal screen.
Connecting/Using a decoder
You can enjoy the variety of programming that is available through
scrambled channels.
Ⅵ S-VHS ET — ON / OFF
When this function is set to “ON”, you can record on VHS
cassettes with S-VHS picture quality. Tapes recorded using this
function can be played back on most S-VHS recorders or VHS
recorders equipped with the S-VHS ET function or VHS recorder
equipped with the SQPB (S-VHS QUASI PLAYBACK) function.
When this function is set to “ON”, the S-VHS indicator lights up
on the display panel.
A Set “L-2 SELECT” to “DECODER”. (੬ 10)
B Connect the recorder’s L-2 IN/DECODER connector to the
decoder’s 21-pin SCART connector using a 21-pin SCART cable.
C Perform the procedure as described in “When receiving a
scrambled broadcast” (੬ 14).
Connecting/Using a stereo system
NOTES:
● Before recording, set “B.E.S.T.” to “ON” (੬ see below).
● You cannot activate the S-VHS ET function while recording
(੬ 7), timer-recording (੬ 8) or Instant Timer Recording (੬ 7)
or the “B.E.S.T.” function (੬ see below) is in progress.
● The S-VHS ET function does not work with S-VHS cassettes.
● To keep the highest quality recording and playback pictures
over a long period of time, S-VHS recording on S-VHS cassettes
is recommended.
You can listen to the soundtrack through your stereo system.
Connect the AUDIO OUT L and R connectors on the recorder to
the AUX IN or TAPE MONITOR connectors on your stereo
system’s receiver or amplifier.
● When listening to sound through the connected stereo system,
turn the TV’s volume down completely.
● Use of high grade tapes is recommended for S-VHS ET
recordings. On some tapes, picture quality will not improve
even if the S-VHS ET function is used. Check the recording
quality before you start important recordings.
Ⅵ B.E.S.T. — ON / OFF
When B.E.S.T. (Biconditional Equalised SignalTracking) system is
set to “ON”, the recorder checks the condition of the tape in use
during playback and recording, and compensates to provide the
highest-possible pictures. When B.E.S.T. works, “bESt” appears
blinking on the display panel. B.E.S.T. takes place whenever you
play back a tape or start recording after inserting a cassette.
NOTE:
The recorder checks the tape condition for about 7 seconds, then
starts recording. To make sure you record the desired scene or
programme completely, perform the following steps:
A Press and hold 9, and press 7. After about 7 seconds, the
recorder re-enters Record Pause mode.
B Press 4 to start recording.
— 11 —
Ⅵ PICTURE CONTROL — AUTO(NORM) / EDIT / SOFT
This function helps you to adjust the playback picture quality
according to your preference.
Ⅵ POWER SAVE — ON / OFF
When this function is set to “ON”, you can reduce the power
consumption while the recorder is turned off.
AUTO(NORM): Normally select this. Picture quality is adjusted
automatically. When “B.E.S.T.” is “OFF”, “NORM” will appear
instead of “AUTO”.
EDIT: Minimizes picture degradation during editing (recording and
playback).
SOFT: Reduces image coarseness when viewing overplayed tapes
containing much noise.
NOTES:
● During Power Save mode,
• the display panel is turned off,
• the Just Clock does not work,
• and the picture may be distorted momentarily when you turn
on/off the recorder.
● Power Save does not work in the following cases:
• When “L-2 SELECT” is set to “DECODER” or “SAT”,
• or when the recorder is in the timer recording standby mode,
• or in the Automatic Satellite Programme Recording mode,
• or when the recorder’s power is turned off after timer-
recording or ITR (Instant Timer Recording).
NOTE:
Select “EDIT” when you are editing tapes. After you finish editing,
select “AUTO”.
Ⅵ AUTO TIMER — ON / OFF
● When this function is set to “ON”:
The timer recording standby mode is automatically engaged when
the recorder is turned off. It is temporarily cancelled when the
recorder is turned on. You do not have to press # to engage or
disengage the timer recording standby mode.
Ⅵ VIDEO STABILIZER — ON / OFF
When this function is set to “ON”, you can automatically correct
vertical vibrations in the picture when playing back unstable
recordings made on another recorder.
● When this function is set to “OFF”:
Press # to engage or disengage the timer recording standby mode.
NOTE:
To watch recordings with close-caption or when you finish
viewing a tape, set this function to “OFF”.
NOTE:
“AUTO TIMER” does not work if “POWER SAVE” is set to “ON”.
Ⅵ S-VHS — ON / OFF
Ⅵ O.S.D. — ON / OFF
You can determine which recording mode — either S-VHS mode
or VHS mode — is used for recording on S-VHS tapes.
● When this function is set to “ON”, you can record on S-VHS
tapes with S-VHS picture quality.
When this function is set to “ON”, various recorder status
information (on-screen display) appears on the screen.
NOTE:
● When this function is set to “OFF”, you can record on S-VHS
tapes with VHS picture quality.
When you use the recorder as the source player for editing a tape,
be sure to set this function to “OFF”. Otherwise, the recorder
status information will be recorded on the edited tape.
NOTES:
● S-VHS mode allows you to make high quality video recordings
with horizontal resolution of 400 lines, comparing with the 230
lines of resolution of conventional VHS recordings. To achieve
the highest quality picture we recommended to record in S-VHS
mode. (But remember that a conventional VHS recorder without
SQPB cannot play back S-VHS tapes recorded in S-VHS mode.)
● S-VHS setting does not affect recording on VHS tapes.
Recording on VHS tapes is always performed in VHS mode
except when using S-VHS ET mode (੬ 11).
Ⅵ AUTO SP]LP TIMER — ON / OFF
When this function is set to “ON”, the recorder automatically
switches to LP mode to allow complete recording if there is not
enough tape to record the entire programme while timer-
recording in SP mode.
For example, recording a programme of 210 minutes in length
onto a 180 minute tape.
Approximately 150 minutes
SP mode
Approximately 60 minutes
LP mode
Ⅵ COLOUR SYSTEM — PAL/NTSC / MESECAM
Total 210 minutes
You can play back PAL, NTSC and MESECAM tapes, or record PAL
and SECAM* signals on this recorder. Select the appropriate
NOTES:
colour system.
● If you have programmed the recorder to timer-record 2 or more
programmes, do not use this function, but change the tape
speed manually during timer programming.
* SECAM signals will be recorded as MESECAM on this recorder;
MESECAM is the designation for tapes with SECAM signals that have been
recorded on a MESECAM-compatible PAL video cassette recorder.
PAL/NTSC: To record PAL signals, or playback a PAL or NTSC tape.
● There may be some noise and sound disturbance where the tape
speed switches from SP to LP mode on the tape.
● This function is not available during ITR (Instant Timer
Recording), and will not work properly with any tapes longer
than E-180 or with some tapes of shorter lengths.
● If you perform timer recording with both this function and VPS/
PDC activated, and the programme goes beyond its originally
scheduled length, sometimes the programme cannot be
recorded in its entirety.
MESECAM: To record SECAM signals, or play back a MESECAM
tape.
NOTES:
About NTSC Playback
● Some TVs shrink the picture vertically and place black bars at
the top and bottom of the screen, or cut off the top and bottom
portions of superimposed displays. This is not a malfunction.
● The picture may roll up and down. This can be corrected if your
TV has the V-HOLD control function.
● The counter and tape remaining time readings will be incorrect.
● During search, still, or frame-by-frame playback, the picture will
be distorted, and there may be a loss of colour.
Ⅵ AUTO POWER OFF — 3H / OFF
When this function is set to “3H”, the recorder turns off
automatically if no operation is done in 3 hours.“AUTO POWER
OFF IN 3MIN” appears on the screen 3 minutes before the
recorder is turned off.
— 12 —
C Select language
Press rt to place the pointer next to the desired language.
Clock Set
Turn on the recorder and the TV, and set your TV to its AV mode
or video channel.
D Perform Auto Channel Set
Press OK twice. When Auto Channel Set is
completed, “SCAN COMPLETED” is
A Access Main Menu screen, then Initial Set screen
displayed on the screen for about
5 seconds, then the Confirmation screen
appears.
Press MENU. Press rt to place the pointer next to “INITIAL
SET”, then press OK or e.
● When you select a country in Central or
Eastern Europe for country setting, station names (ID) are not
stored automatically. Change station names manually. (੬ 14)
B Access Clock Set screen
Press rt to place the pointer next to “CLOCK SET”, then press
OK or e.
E Return to normal screen
Press MENU.
C Set time, date and year
Press rt until the desired time appears,
then press OK or e. Set the date and year
in the same way.
● Holding rt changes the time in
30-minute intervals, or changes the date
in 15-day intervals.
NOTES:
● Depending on reception conditions, the stations may not be
stored in order, and the station names may not be stored
correctly.
● If no sound accompanies the picture or the audio sounds
unnatural on some channels, select the appropriate TV system
for those channels.
● To delete stations with poor reception condition, refer to
“Deleting a channel” (੬ 14).
D Set Just Clock
Set to “ON” or “OFF” by pressing rt, then press OK or e.
Just Clock
The Just Clock function provides accurate time keeping through
automatic adjustments at regular intervals, by reading data from a
PDC signal. Normally, set “JUST CLOCK” to “ON”.
Manual Channel Set
Store channels that were not stored during Auto Set Up or Auto
Channel Set.
NOTES:
● Just Clock may not function properly depending on the
reception condition.
A Access Main Menu screen, then Confirmation screen
Press MENU. Press rt to place the pointer next to “MANUAL
● When you select a country in Central or Eastern Europe for
country setting, you cannot use Just Clock. Skip steps 4 – 5.
● Just Clock is not effective when …
… the recorder’s power is on.
… the recorder is in the Timer mode.
… a difference of more than 3 minutes exists beween the built-
in clock’s time and the actual time.
CH SET”, then press OK or e.
B Select position
Press rt w e until an open channel
position begins blinking, then press OK.
The Manual Channel Set screen appears.
… the recorder is in the Power Save mode (੬ 12).
… “L-2 SELECT” is set to “SAT” (੬ 10).
C Select band
Press rt to select CH (regular) or CC
(cable), then press e.
E Set source channel position
The recorder is preset to receive clock setting and adjustment data
from channel position 1. Press rt to set the channel position to
the number representing the station transmitting clock setting
data, then press OK or e.
D Input channel
Press the number keys to input the
channel number you want to store. Input
“0” before any single number entries.
● To input the registered station name
(ID), press e until “– – – –” begins
blinking, then press rt.
F Start clock
Press MENU.
● When “L-2 SELECT” is set to “A/V” or “SAT”, the “DECODER”
setting cannot be changed. (੬ 10)
● If you have selected a country in Central
or Eastern Europe for country setting,
“TV SYSTEM” setting appears instead of
“DECODER” setting. When you can see
the picture but can hear no audio, select
appropriate TV system.
ATTENTION:
If the AC was disconnected from the recorder and the recorder’s
memory backup has expired, the recorder will automatically
perform Auto Clock Set when the power is restored.
Tuner Set
Perform the following steps only if the tuner has not been set
correctly by Auto Set Up, or if you have moved to a different area,
or if a new station starts broadcasting in your area.
PresseuntilD/KorB/Gblinks.Thenpress
rt to select D/K or B/G.
Major Countries/Areas
TV System
The recorder needs to memorise all necessary stations in channel
positions in order to record TV programmes. Auto Channel Set
automatically assigns all receivable stations in your area.
Austria, Denmark, Finland, Holland, Italy,
Norway, Spain, Switzerland, Sweden,
Germany, Egypt, Western Europe
B/G
China, Mongolia, Rumania, Bulgaria, Czech
Rep., Slovakia, Hungary, Poland, Russia,
Central or Eastern Europe
Auto Channel Set
D/K
A Access Main Menu screen, then Auto Channel Set screen
Press MENU. Press rt to place the pointer next to “AUTO CH
E Store new channel
Press OK.
● Repeat steps 2 – 5 as necessary.
SET”, then press OK or e.
B Select your country
Press rt to place the pointer next to your country, then press OK
F Return to normal screen
Press MENU.
or e.
— 13 —
Deleting a channel
Changing station name
A Access Confirmation screen
Perform step 1 of “Manual Channel Set” (੬ 13).
A Access Confirmation screen
Perform step 1 of “Manual Channel Set” (੬ 13).
B Select position
B Select position
Press rt w e to until the channel you want to delete begins
Press rt w e until the desired channel begins blinking, then
blinking.
press OK twice. The Manual Channel Set screen appears.
C Delete channel
C Select station name
Press &. The channel directly beneath the cancelled one moves
up one line.
If the station name is registered in your
recorder,
● Repeat steps 2 – 3 as necessary.
Press e until the station name (ID) begins
blinking. Press rt until the desired
station name appears, then press OK.
Repeat steps 2 – 3 as necessary.
D Return to normal screen
Press MENU.
Otherwise,
Changing station channel positions
Press e until the first letter of the station
name (ID) begins blinking. Press rt to
cycle through the characters, then press
e. Enter the remaining characters the
same way (maximum of 4). After entering
all characters, press OK.
A Access Confirmation screen
Perform step 1 of “Manual Channel Set” (੬ 13).
B Select position
Press rt w e until the station you want to move begins blinking,
then press OK. The channel number (CH) and the station name
(ID) begin blinking.
● The characters available for the station
name (ID) are A-Z, 0-9, –, *, +, _ (space).
● If you make a mistake, press w until the incorrect character
begins blinking. Then enter the correct character by pressing
rt.
C Select new position
Press rt w e to move the station to the new position, then press
OK.
D Return to normal screen
Press MENU.
Example: If you moved the station in position 4 to position 2, the
stations originally in positions 2 and 3 each move down one
space.
Fine-tuning channels
A Access Confirmation screen
Perform step 1 of “Manual Channel Set” (੬ 13).
B Select position
Press rt w e until the channel you want to tune begins blinking,
then press OK twice. The Manual Channel Set screen appears.
C Perform tuning
● Repeat steps 2 – 3 as necessary.
Press e until “+/–” begins blinking, then press rt until the
picture is its clearest. Then press OK.
● Repeat steps 2 – 3 as necessary.
D Return to normal screen
Press MENU.
D Return to normal screen
Press MENU.
When receiving a scrambled broadcast
NOTE:
When you select a country in Central or Eastern Europe for
country setting, you cannot use decoder with this recorder.
A Select decoder mode
Set “L-2 SELECT” to “DECODER”. (੬ 10)
B Access Confirmation screen
Perform step 1 of “Manual Channel Set”.
C Select position
Press rt w e to select the channel broadcasting scrambled
programmes, then press OK twice.
D Change decoder setting
Press e until “OFF” begins blinking, and set it to “ON” by
pressing rt. Then press OK.
● Repeat steps 3 – 4 as necessary.
E Return to normal screen
Press MENU.
— 14 —
TV station and ID list
Video Channel Set
Video channel (RF output channel) is the channel on which your
TV receives picture and sound signals from the recorder through
the RF cable.
ID*
STATION NAME
ID*
STATION NAME
1000
3SAT
9LIV
TV1000
3SAT
NICK
NOVA
NRK1
NRK2
ODE
ORF1
ORF2
PHOE
POLS
PREM
PRIM
PRO7
RAI1
RAI2
RAI3
RET4
RTB1
RTB2
RTL
NICKELODEON
NOVA TV
NRK
9LIVE
Perform the following steps only if —
— Video Channel Set has not been done correctly by the Auto Set
Up function (੬ 4),
— interference appears in the TV picture after you have moved to
a different area or a new station has started broadcasting in your
area,
— you change the connection between your recorder and TV
from RF connection toAV connection, or vice versa.
If you have connected the recorder to your TV via the AV
connection (੬ 4), set the video channel to off.
If you have connected the recorder to your TV via the RF
connection (੬ 4), set the correct video channel.
● Make sure the recorder’s power is off and there is no cassette
inserted in the recorder.
AB3
AB3
ADULT
Animal Planet
ANTENA3
ARD
ARTE
ATV
BERLIN1
BBC GROUP
BBC1
BBC2
BBCW
TV BIO+
BLOOMBERG
BAYERN3
CANAL PLUS
PORTUGUSES
C9
NRK2
ADLT
ANIM
ANT3
ARD
ARTE
ATV
ODEON
ORF1
ORF2
PHOENIX
POLST
PREMIERE
PRIMA TV
PRO7
B1
BBC
BBC1
BBC2
BBCW
BIO+
BLOO
BR3
RAI1
RAI2
RAI3
RETE4
TELE21
RTBF2
RTL
C+
C1
RTL2
RTL4
RTL5
RTL7
RTLK
RTP
RTL2
C9
RTL4
CAN5
CANV
CANZ
CH4
CH5
CHLD
CINE
CLUB
CMT
CNN
CSUR
CT1
CANALE5
KETNET CANVAS
KANAAL Z
CHANNEL4
CHANNEL5
CHILD
RTL5
RTL7
A Access Video Channel Set mode
RTL KLUB
RTP
Hold down 0 on the recorder until the
RTV4
SAT1
SBS6
SERV
SF1
RTV4
SAT1
display panel shows the following.
CINEMA
TELECLUB
CMT
SBS
Service
SF1
B Set RF output system
The blinking number on the display
indicates the RF output system of your
country. Press rt to set to “1” or “2”, then
press OK. (1 :B/G 2 :D/K)
CNN
SF2
SF2
ANDALUCIA
CT 1
SHOW
SIC
SHOW
SOCIEDADE
SKY CHANNEL
SKY NEWS
SPEKTRUM
SPORT
SUPER RTL
STAR-TV
SVT1
CT2
CT 2
SKY
DISC
DK1
DISCOVERY
TV Denmark 1
TV Denmark 2
Denmark 4
DR TV
SKYN
SPEK
SPRT
SRTL
STAR
SVT1
SVT2
SV24
SWR
TCC
DK2
Major Countries/Areas
TV System
DK4
DR1
Austria, Denmark, Finland, Holland, Italy,
Norway, Spain, Switzerland, Sweden,
Germany, Egypt, Western Europe
DR2
DR2
DSF
DSF
SVT2
News
B/G
DUNA
ETB1
ETB2
ETV
DUNA TV
ETB1
SUEDWEST3
TCC
ETB2
China, Mongolia, Rumania, Bulgaria, Czech
Rep., Slovakia, Hungary, Poland, Russia,
Central or Eastern Europe
Game/Shop/Music
EURO NEWS
EURONEWS
EUROSPORTS
FEMMAN
FILM
TCM
TELE
TEL5
TF1
TCM
EUNW
EURO
EUSP
FEMM
FILM
FNET
FR2
FR3
FR5
GALA
HBO
HR3
HSEU
INFO
ITA1
ITA7
ITV1
JIM
TELE
D/K
TELE5
TF1
TM
TM
TMC
TMF
TNT
TELEMONTECARLO
TMF
C Set video channel
With AV connection
Press PR – until the display panel shows
“1 – –” (or “2 – –”).
● Now the video channel is set to off.
FILMNET
France2
France3
France 5
GALAVISION
HBO
TNT INT
TRT INT
TSI
TRT
TSI1
TSI2
TSI2
TSR1
TSR2
TV1
TSR
HESSEN3
HSEU
TSR2
BRTN TV1
TV2
With RF connection
INFO-KANAL
ITALIA1
ITALIA7
ITV
TV2
Press PR + or – to set the video channel to a vacant position
between 22 and 69 which is not occupied by any local station in
your area.
TV2Z
TV3
TV2 Z
TV3
TV3+
TV4
TV3 plus
TV4
JIM TV
(Example) If channel 50 is available in your
area, set the video channel to 50.
Then, set your TV to UHF channel 50.
● If the two vertical white bars appear
clearly on the screen as shown on the right, go
to step 4.
● If the two vertical white bars do not appear
clearly, re-set the video channel to another
vacant position and try again.
JSTV
KA2
JSTV
TV5
TV5
KA2
TV6
TV6
KAB1
KAN2
KAN5
KBH
KIKA
LA7
KABEL1
KANAL2
KANAL5
Kbh. Kanal
Kinder kanal
LA7
TV8
TV8
TVE1
TVE2
TVG
TVI
TVE1
TVE2
TV GALICIA
TV INDEPENDENT
TV NORGE
TVN24
TVP1
TVN
TV24
TVP1
TVP2
TV P
V8
VCR
VH-1
VIT
VIVA
VIV2
VMTV
VOX
VSAT
VT4
LIB
Liberty TV
LOCAL
LOCA
M6
M6
TVP2
TV Polonia
V8
VIDEO
VH-1
VIT
VIVA
VIVA2
VIDEO MUSIC
VOX
VIASAT3
VT4
VTM
West3
WRLD
YLE1
YLE2
YORIN
ZDF
ZTV
MBC
MCM
MDR
MOVE
MTV
MTV1
MTV2
MTV3
NGEO
N24
MBR
MCM
MDR
D Exit Video Channel Set mode
Press OK.
MOVIE
MTV
MTV1
MTV2
MTV3
With AV connection
To view picture signals from the recorder, set your TV to its AV
mode.
NGEO
News 24
NORD3
N-TV
N3
N-TV
NBC
NDR
NED1
NED2
NED3
NET5
NEWS
VTM
WDR3
WRLD
YLE1
YLE2
YORN
ZDF
With RF connection
NBC SUPER
NDR
The channel on which the two vertical white bars appear
clearly is your video channel. To view picture signals from the
recorder, set your TV to the video channel.
NED1
NED2
NED3
Net 5
ZTV
* The “ID” abbreviation is what is shown on-screen in lieu of the
station name. The “ID” abbreviation is listed in the Confirmation
screen and is displayed on the screen when the recorder is
tuned to a different station.
— 15 —
TUNER/TIMER
TV channel storage
capacity
Specifications
: 99 positions (+AUX position)
: Frequency synthesized tuner
Tuning system
Channel coverage
VHF
GENERAL
Power requirement
Power consumption
Power on
: AC 220 V – 240 Vd, 50 Hz/60 Hz
: 47 MHz – 89 MHz/
104 MHz – 300 MHz/
302 MHz – 470 MHz
: 16 W
: 3.5 W
Power off
UHF
: 470 MHz – 862 MHz
Temperature
Operating
Storage
Operating position
Dimensions (W x H x D) : 400 mm x 94 mm x 270 mm
Weight
Format
Maximum recording time
Aerial output
Memory backup time
: UHF channels 22 – 69 (Adjustable)
: Approx. 10 min.
: 5°C to 40°C
: –20°C to 60°C
: Horizontal only
ACCESSORIES
Provided accessories
: RF cable,
Infrared remote control unit,
Lithium battery – CR2032 –
: 3.1 kg
: S-VHS/VHS PAL standard
(SP)
(LP)
: 240 min. with E-240 video cassette
: 480 min. with E-240 video cassette
Specifications shown are for SP mode unless specified otherwise.
E. & O.E. Design and specifications subject to change without
notice.
VIDEO/AUDIO
Signal system
: PAL-type colour signal and CCIR
monochrome signal, 625 lines
50 fields
Recording system
: DA4 (Double Azimuth) head helical
scan system
Signal-to-noise ratio
Horizontal resolution
VHS
: 45 dB
: 250 lines
: 400 lines
S-VHS
Frequency range
Normal audio
Hi-Fi audio
: 70 Hz to 10,000 Hz
: 20 Hz to 20,000 Hz
Input/Output
: 21-pin SCART connectors:
IN/OUT x 1, IN/DECODER x 1
RCA connectors:
AUDIO OUT x 1
— 16 —
|