Westinghouse Flat Panel Television MT80 THIN User Manual

Installation and Assembly:  
Universal Flat Wall Mount for 22" - 37" Screens  
Model: MT80 THIN  
Features:  
R
Universal design for 22" to 37" plasma and LCD screens  
Low-profile design keeps the screen close up against the wall  
Max Load Capacity: 80 lb (36.3 kg)  
For customer service call 1-866-287-5555.  
ISSUED: 03-02-05 SHEET #: 201-9323-1  
 
Before you begin, make sure all parts shown are included with your product.  
Parts List  
MT80 THIN  
Qty Part #  
Description  
wall plate  
adapter bracket  
#14 x 2.5" wood screw  
M5 x .8 x 25 mm socket head cap screw  
Alligator® anchor  
1
2
4
2
4
1
200-4629  
AA  
BB  
CC  
DD  
EE  
FF  
200-4628  
5S1-015-C04  
520-9567  
590-0097  
560-1145  
4 mm security allen wrench  
AA  
BB  
FF  
DD  
EE  
CC  
ISSUED: 03-02-05 SHEET #: 201-9323-1  
3 of 8  
For customer service call 1-866-287-5555.  
 
Installation to Single Wood Stud Wall  
WARNING  
• Installer must verify that the wall will safely support four times the combined weight of all attached equipment and  
hardware.  
Use stud finder to locate stud centers. Place wall plate (AA) on wall as template, level wall plate and mark center  
of studs with pencil. Drill three 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Attach wall plate (AA) using three #14  
x 2.5" wood screws (CC).  
1
Skip to step 2 on page 7.  
WARNING  
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the  
screws, greatly reducing their holding power.  
• Never tighten in excess of 80 in. • lb (9 N.M.).  
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is  
highly recommended.  
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-  
ers are responsible to provide hardware for other types of mounting situations.  
AA  
CC  
ISSUED: 03-02-05 SHEET #: 201-9323-1  
4 of 8  
For customer service call 1-866-287-5555.  
 
Installation to Double Wood Stud Wall  
WARNING  
• Installer must verify that the wall will safely support four times the combined weight of all attached equipment and  
hardware.  
Use stud finder to locate stud centers. Place wall plate (AA) on wall as template, level wall plate and mark center  
of studs with pencil. Drill four 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Attach wall plate (AA) using four #14 x  
2.5" wood screws (CC).  
1
Skip to step 2 on page 7.  
WARNING  
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the  
screws, greatly reducing their holding power.  
• Never tighten in excess of 80 in. • lb (9 N.M.).  
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is  
highly recommended.  
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-  
ers are responsible to provide hardware for other types of mounting situations.  
AA  
CC  
ISSUED: 03-02-05 SHEET #: 201-9323-1  
5 of 8  
For customer service call 1-866-287-5555.  
 
Installation to Solid Concrete or Cinder Block  
WARNING  
• When installing Westinghouse wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual con-  
crete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a  
solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifica-  
tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to  
avoid breaking out the back of the hole when entering a void or cavity.  
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.  
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware  
and components.  
Use wall plate (AA), making sure that it is level, as  
concrete  
surface  
1
a template to mark holes. Drill four 1/4" (6 mm) dia.  
holes to a minimum depth of 2-1/2" (64 mm). Insert  
anchors (EE) in holes flush with wall as shown  
(right). Place wall plate over anchors and secure  
with #14 x 2.5" screws (CC). Tighten all fasteners.  
1
EE  
Drill holes and insert anchors (EE).  
2
AA  
CC  
WARNING  
• Tighten screws so that wall plate is firmly attached,  
but do not overtighten. Overtightening can damage  
screws, greatly reducing their holding power.  
EE  
• Never tighten in excess of 80 in. • lb (9 N.M.).  
Place plate (AA) over anchors (EE) and secure with  
screws (CC).  
3
WARNING  
• Always attach concrete expansion anchors directly to  
load-bearing concrete.  
• Never attach concrete expansion anchors to con-  
crete covered with plaster, drywall, or other finishing  
material. If mounting to concrete surfaces covered  
with a finishing surface is unavoidable, the finishing  
surface must be counterbored as shown below. If  
plaster/drywall is thicker than 5/8", custom fasteners  
must be supplied by installer.  
Tighten all fasteners.  
EE  
AA  
CC  
CORRECT  
INCORRECT  
wall plate  
concrete  
concrete  
wall  
plate  
plaster/  
drywall  
plaster/  
drywall  
ISSUED: 03-02-05 SHEET #: 201-9323-1  
6 of 8  
For customer service call 1-866-287-5555.  
 
Note: Before starting this step refer to accompanying instruction sheet to install adapter brackets to flat panel screen.  
Installing Flat Panel Screen to Wall Plate  
Insert two M5 x 25 mm socket head cap screws (DD) into mounting brackets (BB) and tighten a few turns to hold in  
place as shown in detail 1. Hang screen by the mounting brackets (BB) on wall plate (AA) as shown below. Make  
2
sure screen is safely hooked on mount before letting go. Screen can be adjusted horizontally if desired.  
WARNING  
• Always use an assistant or mechanical lifting equip-  
ment to safely lift and position the plasma television.  
BB  
BB  
AA  
detail 1  
Adding Safety to Mount  
Secure mounting brackets to wall plate (AA) with socket head cap screws as shown below and in detail 1. Tighten  
screws with 4 mm security allen wrench (FF).  
3
BB  
DD  
AA  
DETAIL 1  
ISSUED: 03-02-05 SHEET #: 201-9323-1  
7 of 8  
For customer service call 1-866-287-5555.  
 
Limited Five-Year Warranty  
Westinghouse Digital Electronics warrants to original end-users of this Westinghouse television mounting product (the  
“Product”) that the Product will be free from defects in material and workmanship, under normal use, for a period of five (5)  
years from the date of purchase by the original end-user, subject to the following terms and conditions:  
REPAIR OR REPLACEMENT – For a period of five (5) years from the original date of purchase, Westinghouse Digital  
Electronics will repair any defect in material or workmanship in the Product, or, at its option, replace a defective Product.  
Replacement parts and products will be warranted for either the remainder of the original warranty period or ninety (90)  
days from the date of delivery to the end-user, whichever occurs last.  
OBTAINING WARRANTY SERVICE To obtain warranty services, you must either personally deliver or ship the Product  
to Westinghouse Digital Electronics, freight prepaid. Please call Westinghouse Digital Electronics at (866) 287-5555 to  
obtain a Return MerchandiseAuthorization (“RMA”) and for other instructions regarding return and replacement or repair of  
the Product. Westinghouse Digital Electronics will not accept Products delivered to it without an RMA.  
EXCLUSIONS TO WARRANTY – This warranty does not cover damage caused by (a) service or repairs by anyone other  
than personnel authorized by Westinghouse Digital Electronics, (b) the failure to utilize proper packing when returning the  
product, (c) improper installation or the failure to follow Product instructions or warnings, or (d) misuse or accident, in  
transit or otherwise.  
PROOF OR ORIGINAL PURCHASE Asales receipt, invoice, or other proof of purchase specifying the original date of  
purchase within the five (5) year warranty period must be presented to obtain warranty service. This warranty extends to  
the original purchaser and is not transferable.  
EITHER REPAIR OR REPLACEMENT IS YOUR EXCLUSIVE REMEDY UNDER THIS WARRANTY. EXCEPT TO THE  
EXTENT PROHIBITED BY LAW, WESTINGHOUSE DIGITAL SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR  
CONSEQUENTIAL DAMAGES CLAIMED TOARISE FROM BREACH OFANY EXPRESS OR IMPLIED WARRANTY ON  
THIS PRODUCT. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FORA PARTICULAR PURPOSE  
ON THIS PRODUCT IS LIMITED IN DURATIONAND SCOPE TO THE TERMS OF THIS WARRANTY.  
Some States do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how  
long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives specific legal rights, and  
you may also have other rights which vary from State to State.  
Westinghouse Digital Electronics, LLC  
16257 East GaleAve.  
City of Industry, California 91745  
Tel: (626) 333-9677.  
ISSUED: 03-02-05 SHEET #: 201-9323-1  
8 of 8  
For customer service call 1-866-287-5555.  
andWestinghousearetrademarksofWestinghouseElectricCorporationandareusedunderlicense.  
 
Installing Adapter Brackets to  
the Flat Panel Screen  
Model: MT80 THIN  
Begin with product installation and assembly manual before reading this instruction manual.  
Parts List  
Description  
Qty. Part #  
A M4 x .7 x 12 mm phillips screw  
C M4 x .7 x 25 mm phillips screw  
E M5 x 40 mm pan head phillips scew  
F M6 x 25 mm pan head phillips screw  
G M6 x 1 x 20 mm pan head phillips screw  
H M5 x .8 x 12 mm pan head phillps screw  
6
6
4
4
4
4
6
6
6
4
4
504-9013  
504-1015  
520-1199  
520-1208  
520-9402  
520-1027  
520-1128  
520-9543  
580-1036  
590-1106  
580-1067  
I
M6 x 1 x 12 mm pan head phillips screw  
K M5 x 25 mm pan head phillips screw  
O multi-washer  
S .25" ID x .5" OD x .625" H nylon spacer  
V .251" ID x .5" OD x 1.25" H aluminum spacer  
BB  
Note: This part is listed on the  
productinstallationandassem-  
bly manual.  
A
K
C
E
F
G
H
I
O
S
V
ISSUED: 01-18-05 SHEET #: 201-9325-1  
For customer service call 1-866-287-5555.  
1 of 4  
 
To assemble the adapter brackets to your screen, begin with the table on pages 2 and 3. Find the configuration  
that corresponds to your screen. Refer to the configuration table on page 3 to install the adapter brackets.  
Notes: The Universal Flat Wall Mountis a universal mount which accommodates a wide variety of screens. If your particular  
screen is not listed on pages 2 and 3 or unsure which configuration matches your screen, please contact customer service  
to ensure product compatibility.  
Screen  
Manufacturer  
Manufacturer Model  
Config.  
Size  
LCD Screens  
Akai  
BenQ  
22"  
30"  
23"  
23"  
26"  
30"  
23"  
26"  
30"  
23"  
LC2260  
K
A
K
K
A
A
K
A
A
K
K
K
K
F
F
K
K
A
F
A
A
A
I
DV3070 (DV3080)  
H2300  
W2300  
CTX  
Dell  
Dell  
Dell  
W2600  
W3000  
Gateway  
Gateway  
Gateway  
Hewlett Packard  
IBM  
GTW-L23M102  
GTW-L26M103  
GTW-L30M103  
f2304  
22.2" T221  
FP2400MAX  
LT23X475  
Image Systems  
JVC  
JVC  
24"  
23"  
26"  
32"  
22"  
23"  
27"  
30"  
30"  
30"  
32"  
30"  
22"  
27"  
30"  
22"  
30"  
30"  
30"  
30"  
27"  
30"  
22"  
26"  
32"  
32"  
LT26WX84, LT26X575  
LT32WX84, LT32X575  
285LT, 295LM  
JVC  
LG  
LG  
RU-23LZ21, RU-23LZ50C, L2320A, L2323T  
RU-27LZ50C  
L3000A  
LG  
LG  
LG  
LG  
L3020T, RU-30LZ50C  
DU-30LZ30  
LG  
Maxx Products  
Luce  
RU-32LZ50C  
MAXX 3000  
LCTV2201A / GB  
MX-27X1  
MX-30X1  
K
A
A
K
A
A
A
I
MAXENT  
MAXENT  
Mitsubishi  
Mitsubishi  
Mitsubishi  
NEC-Mitsubishi  
Net TV  
Ovideon  
Ovideon  
Panasonic  
Panasonic  
Panasonic  
Panasonic  
Philips  
Philips  
Philips  
Philips  
Philips  
PixelPro  
PixelPro  
Planar  
Planar  
Samsung  
Samsung  
Samsung  
Sceptre  
Sceptre  
Sharp  
LT-2220, LT-2240  
LT-3020, LT-3040, LT-3050  
MLM300  
LCD3000  
LCTV-30W  
LC2700w  
LC3000W  
TC-22LH1  
TC-26LX20  
A
A
K
C
C
C
K
K
K
A
F
A
A
K
K
K
K
A
K
A
A
A
L
TC-32LX20  
TC32LH1  
23" 23FW995/997, 23PF9945  
23" 23PF8946, 23PF8946A  
23" 23PF9966  
26"  
30"  
27"  
30"  
22"  
26PF9966  
30PF9975, 30FW9955, 30FW9975, 30FW995, 30FW997  
PX-27XP10  
PX-30XP10  
XP22WSA-01  
23.1" WS231  
22"  
24"  
26"  
23"  
30"  
26"  
30"  
32"  
37"  
23"  
23"  
23"  
26"  
30"  
LTM225W, LTN226W  
Syncmaster 204T, 240T, 243T  
LT-P266W  
Naga X23S  
X30SV- Naga III  
LC-26GA4U, LC-26GD4U, LC-26GD6U  
LC-30HV2U, LC-30HV4U, LC-30HV6U  
LC-32G4U, LC-32GD4U, LC-32GD6U  
LC-37HV4U, LC-M3700, LC-37HV6U, LC-37G4U, LC-37GD4U, LC-37GD6U  
LMD-230WS  
Sharp  
Sharp  
Sharp  
L
Sony  
Sony  
K
K
K
A
F
KLV-23HR2, SDM-232W/B  
KLV-23M1  
Sony  
Sony  
Sony  
KLV-26HG2  
KLV-30XBR900, KLV-30XBR950, LDM3000  
Continued on the following page...  
ISSUED: 01-18-05 SHEET #: 201-9325-1  
For customer service call 1-866-287-5555.  
2 of 4  
 
Screen  
Size  
Manufacturer  
Manufacturer Model  
Config.  
Sony  
Sony  
32"  
32"  
30"  
27"  
30"  
23"  
27"  
30"  
26"  
26"  
32"  
22"  
KDL-32XBR950  
KLV-32M1  
SELCD300  
LT27HV  
G
A
I
Studio Experience  
Syntax  
Syntax  
A
A
K
A
A
A
A
A
K
K
K
I
LT30HV  
V23CLTT  
Tatung  
Tatung  
V27CMTT  
V30CMTT  
Tatung  
Toshiba  
26HL83  
26HL84  
Toshiba  
Toshiba  
32HL84  
LCD-2200VT, LCD-2216TD  
ToteVision  
ViewSonic  
ViewSonic  
Viewsonic  
Viewsonic  
Viewsonic  
Westinghouse  
Westinghouse  
Westinghouse  
Westinghouse  
Westinghouse  
Westinghouse  
Westinghouse  
Zenith  
22.2" VP2290b  
23"  
27"  
30"  
30"  
27"  
27"  
30"  
30"  
32"  
37"  
37"  
23"  
27"  
VP230mb  
N2700w  
N3000w  
C
C
A
A
C
A
A
A
A
K
A
N3020w  
LTV-27w2  
W32701  
LTV-30w2  
W33000, W33001  
LTV-32w1  
LTV-37w2 HD  
LVM-37w1  
L23W36  
Zenith  
L27W46  
Plasma Screens  
Eiki  
Hitachi  
Hitachi  
32"  
32"  
37”  
32"  
32"  
32"  
37"  
32"  
32"  
32"  
PLD-32U  
G
B
B
I
32HDT20, 32HDT50, 32HDT55, 32HDT60  
CMP307SX, CMP307U, CMP307XU  
MAXX 3200  
Maxx Products  
Monovision  
Philips  
PD3231  
32FD9954, 32FW997  
I
F
F
G
H
I
Philips  
Sanyo  
37FD9944, 37FD9954/17, 37PF9965  
PDP-32H1A  
Sony  
Studio Experience  
KZ-32TS1U, KZ-32TS1, KE-32TS2  
SEPD3200, SEPD3231  
Using your screen's configuration letter from the  
previous table, find the configuration that  
TOP  
1
TOPHOLEFORM5SCREWS  
MIDDLEHOLEFORM4SCREWS  
BOTTOMHOLEFORM6SCREWS  
O
corresponds to your screen. Refer to the table  
below to find which fasteners to use when installing  
the adapter brackets and use the corresponding  
hole in the multi-washer (O) that matches your  
screw size as shown in figure 1.  
Config. Screws Spacer  
BOTTOM  
A
B
C
F
G
H
I
*K  
**L  
A
I
no  
no  
S
no  
S
V
S
no  
no  
fig. 1  
C
H
K
E
F
A
I
**Note: If screws (A) do not engage with four complete  
turns, then use screws (C) with spacer (S).  
**Note: If screws (I) do not engage with the threads  
inside the mounting hole then use screws (G).  
If screws (G) are not long enough then use  
screws (F).  
ISSUED: 01-18-05 SHEET #: 201-9325-1  
3 of 4  
For customer service call 1-866-287-5555.  
 
Installing Adapter Brackets  
To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place  
screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached.  
Place adapter brackets (BB) on back of screen, align to holes, and center on back of screen as shown in figure 2.1.  
Refer to step 1 to determine the proper fasteners to use. Attach the adapter brackets to the back of the screen using  
the appropriate combination of screws, multi-washers (O), and spacers as shown in figure 2.2. Verify that all holes are  
properly aligned, and then tighten screws using a phillips screwdriver.  
2
X
WARNING  
• Tighten screws so adapter brackets are firmly  
attached. Do not tighten with excessive force.  
Overtightening can cause stress damage to  
CENTERBRACKETSVERTICALLY  
ONBACKOFSCREEN  
screws, greatly reducing their holding power and  
possibly causing screw heads to become  
detached. Tighten to 40 in. • lb (4.5 N.M.)  
maximum torque.  
Notes:  
• The number of fasteners used will vary,  
depending upon the type of screen.  
BB  
BB  
• Spacers may not be used, depending upon  
the type of screen.  
X
fig 2.1  
Note: "X" dimensions should be equal.  
BB  
SCREWS  
O
BB  
SPACERS  
fig 2.2  
ISSUED: 01-18-05 SHEET #: 201-9325-1  
For customer service call 1-866-287-5555.  
4 of 4  
andWestinghousearetrademarksofWestinghouseElectricCorporationandareusedunderlicense.  
 

Weed Eater Trimmer 545186797 User Manual
Weider Home Gym WEBE09200 User Manual
Whirlpool Freezer ED25SMIII User Manual
Williams Sound Video Game Sound System Model WIR 237 Model WIR 238 Model WIR 239 User Manual
Windsor Vacuum Cleaner 98165 User Manual
Xilinx Network Card v100a User Manual
Zanussi Cooktop EB2465 User Manual
Zanussi Oven ZDQ 695 User Manual
Zanussi Washer ZWF 14380 S User Manual
Zeki Tablet TBQC1063B User Manual